Aluminum board process-B

5.4 board inspection
5.4.1 line surface must be in accordance with the requirements of the MI to check all the content.
5.4.2 must check on aluminum surface, aluminum surface dry film cannot have film falls and broken.
5.5 etching
5.5.1 for copper base is commonly 4 oz, will there is a certain difficulty in etching.First plate must be approved by the captain in person to do board, made in the spot check, line width, line spacing should be strengthened once every 10 PNL plate spot check line width, and make records.
5.5.2 recommended parameters: speed: 7 ~ 11 dm/min pressure: 2.5 kg/cm2 proportion: 25 be temperature: 55 ℃ (the above parameters are for reference only, the test plate results shall prevail)
5.5.3 back membrane should be paid attention to the time of the control between 4 ~ 6 min, because aluminium will reaction with NaOH, but also must ensure that the membrane clean, backing down membrane liquid membrane was not allowed to turn up the heat.No protective film of the plate, aluminum, from liquid membrane in the back up after the board will not stay to wash water on a board in time of liquid membrane, prevent the alkali corrosion of aluminum surface.  
5.6 corrosion inspection
5.6.1 normal board.
5.6.2 it is forbidden to use the blade repair line, in order to avoid injury and dielectric layer.
5.7 the solder mask
5.7.1 production process:
Brush copper surface grinding plate (only) to screen printing green oil (the first), and preliminary drying screen printing green oil (second) and the preliminary drying - exposure and development - plate mill, the acid pickling process. Under the soft brush - after curing -
5.7.2 reference parameters:
5.7.2.1 yarn used 36 t + 100 t
First 75 ℃ 5.7.2.2 x 20-30 min;The second 75 ℃ x 20-30 min
5.7.2.3 exposure: 60/65 (single) 9 ~ 11
5.7.2.4 enhancement: speed: 1.6 ~ 1.8 m/min pressure: 3.0 kg/m2 (total pressure)
5.7.2.5 curing: after 90 ℃ * 60 min + 60 min + 110 ℃ 150 ℃ above x 60 min parameters for the use of the DSR - 2200 tl ink, used only for reference.
5.7.3 note printing for control of air bubbles, if need, can add 1-2% of the diluent.
5.7.4 clappers before clappers member should check panel, there is a problem of instruct the captain and then to the clapper.   
5.8 HASL
5.8.1 spray before tin for aluminum plate with protective film tear protective film after spray tin.    
5.8.2 edge with both hands, it is strictly prohibited by hand directly touch the plate (especially aluminum surface).
5.8.3 operation, fight chafed.
5.8.4 tin cookie sheet before 130 ℃, 1 hour, and baking sheet to spray tin interval time less than 10 minutes.In order to avoid temperature difference cause a layered with ink.    
5.8.5 rework plate spray is only allowed to return once, if more than one board, to distinguish for special treatment.    
5.9 aluminum surface passivation treatment
5.9.1 level passivation process: (1) scrubbing brush (500 #) to (2) water - > (3) passivation, (4) washing the x 3-5. Dry - 6 drying
Note: (1) grinding plate: only aluminum surface grinding, FR4 parameter grinding plate.First board to check line no scratches, as well as the tin cried, uniform grinding crack.
(3)passivation: potion ingredients open cylinder quantity cylinder volume liquid temperature control concentration spraying in tank pressurization rate
Na2CO3 (CP) 50 g / 6500 g l, 130 l, 40 ~ 50 ℃ 2.0 ~ 3.0 1.0 ~ 1.5 m/min effective soaking time 10 ~ 15 s 100 m2 CP (K2CrO4) 15 g/l,  1950 g NaOH (CP) 390 g, 3 g/l
6 drying: 80 ~ 90 ℃.
Tyle = "the oledata.mso - spacerun: 'yes', the font size: 10.5000 pt; the font-family:" tahoma "; "> 5.7.2.5 curing: after 90 ℃ * 60 min + 60 min + 110 ℃ 150 ℃ above x 60 min parameters for the use of the DSR - 2200 tl ink, used only for reference.
5.7.3 note printing for control of air bubbles, if need, can add 1-2% of the diluent.   
5.7.4 clappers before clappers member should check panel, there is a problem of instruct the captain and then to the clapper.  

Where to Find High Quality PCB'A

Great Offer In May

Order PCB’A, of which value up to $2000,immediately breaks $100.

—Come to “Wonderful PCB” for PCB’A

—20 Years of Experience

—High Quality Assurance

Promotion time: May 8th,2015 - June 10th,2015

Flex PCB - What is Flex PCB

FPC and the birth and development of the PCB, Rigid-Flex PCB gave birth to this new product. Therefore, Flex PCB is flexible circuit board and rigid circuit boards, after lamination processes, according to the relevant process requirements together, forming characteristics have FPC PCB board characteristics.

1.Flex PCB - Production Process：

Because Flex PCB is a combination of FPC and the PCB, Flex PCB production should also have the FPC PCB production equipment and production equipment. First, the combination of soft board electronics engineer to draw a line and shape according to demand, then, can be issued to the Flex PCB production plant, through CAM engineers relevant documents for processing, planning, and then arrange FPC production line production need FPC, PCB production line to produce PCB, after these two soft board and hard board out, according to the planning requirements for electronic engineers, the FPC and PCB through seamless lamination lamination machine, and then through a series of detailed links, ultimately process the Flex PCB. A very important aspect should Flex PCB difficult, more details before shipping, are generally required to conduct the inspection, its value is relatively high, so as not to let the supply and demand sides related loss of interest.

2. Flex PCB - Advantages and Disadvantages：

Advantages: FPC Flex PCB along with features and characteristics of the PCB, so it can be used in some special requirements of the product among the region has some flexibility, but also have a certain rigidity region of the internal space-saving products reduce the volume of the finished product, improve product performance is very helpful.

Cons: Flex PCB production process many, difficult to produce low yields, cast materials, manpower more, so its price is more expensive, relatively long production cycle.

3. Flex PCB - Related Applications

Flex PCB's characteristics determine its application in all areas covered by FPC PCB applications, such as:

1.Mobile telephone

2.Keypad and side buttons, etc.

3.Computer and the LCD screen

Such as motherboards and display

a.CD Walkman

b.Drives

c.NOTEBOOK.

4. New Uses

Components of a hard disk drive (HDD, hard disk drive) suspension circuit and xe packaging board, etc.