显示标签为“China Aluminum pcb”的博文。显示所有博文
显示标签为“China Aluminum pcb”的博文。显示所有博文

2015年3月23日星期一

Aluminum PCB board Application

Led aluminum pcb thermal conductivity
Led aluminum board and thermal conductivity aluminum board in the middle of the insulating layer (generally is PP, now has a thermal conductive adhesive, etc.), it is one of the three major measure of aluminum plate quality, heat resistance and pressure value is another two performance).Aluminum plate thermal conductivity can be tested after plate bonding instrument tests data, the high value of thermal conductivity is generally ceramic, copper, etc., but due to the cost into consideration, is currently on the market mainstream electronic aluminum plate, aluminum plate thermal conductivity of the corresponding is parameters of people's concern, the higher the coefficient of thermal conductivity is one of the symbols of the better performance.

Led aluminum plate classification
Led fluorescent lamp aluminum plate is aluminum plate classification, street light aluminum plate, tube light aluminum plate, wall lamp aluminum plate, shoot the aluminum plate, energy-saving light aluminum plate, electrodeless lamp aluminum plate, aluminum board, ceiling aluminum plate, wash wall lamp aluminum plate, the ball bubble lamp aluminum plate, tunnel light aluminum plate, floodlight, aluminum plate, aluminum plate, wall lamp high-power aluminum plate, small power aluminum plate, guardrail tube aluminum plate, neon lights aluminum plate, corn lamp aluminum plate, the candle light aluminum plate, absorb dome light aluminum plate, kitchen lamp aluminum plate, corridor lights aluminum plate, buried lights aluminum plate, dared light aluminum plate, industrial and mining lamp aluminum plate, aluminum plate bridge lights, floor tile lamp aluminum plate, stair light aluminum plate.

LED aluminum plate insulating layer
LED aluminum plate insulation layer is one of the most core technology of aluminum plate, the main adhesive, insulation and thermal conductivity of the function.Aluminum base board insulation is a power module.
Structure of the largest thermal barrier.Insulation heat conduction performance, the better, the more conducive to the spread of the heat produced during the operation, will be conducive to reduce the operating temperature of the device, so as to improve the module of power load, reducing the volume and prolong life, improve the power output, etc.
LED aluminum plate
1, audio equipment: input, output amplifier, balanced amplifier, audio amplifier, preamplifier, power amplifier, etc.   
2, power equipment, switching regulator ` DC/AC converter ` SW regulator, etc.   
3, communication electronic equipment: high frequency increase ` filtering electrical ` transmitting circuit.   
4, office automation equipment, motor drives, etc.    
5, automobile, electronic regulator ` igniter ` power controller, etc.   
6, a computer: CPU board ` diskette drive ` power supply device, etc.   
7, power module, inverter ` solid relay ` rectifier bridge, etc

2015年3月4日星期三

WonderfuI Printed Circuit Board

From the number of layers and the development direction of PCB board to points, the PCB industry into a single panel, double panel, conventional multilayer flexible board, HDI (high density interconnect) board, package substrate and other six major product segments . From the product life cycle "lead-in period - growing - maturity - a recession" and four-cycle dimension view, where a single panel, double panel electronics products because they do not fit the current trends in the application of thin short, is in recession, its value gradually reduce the proportion of developed countries and regions such as Japan, Korea and Taiwan has been very little in the local production of such products, many manufacturers have made it clear that no longer meet single and double panel. Conventional multilayer and HDI products, process capability maturity are more sophisticated, higher value-added products, is currently the most major PCB factory full Zhugong direction, Chinese manufacturers are only a handful of ultrasound and electronic production techniques; scratch plates, especially high-density flexible and rigid PCB board, due to the current technology is not yet mature, a lot of manufacturers failed to achieve mass production of products are growing, but because it has more than a rigid plate adapted to digital products features flexible plate growth is high, is the future direction of the various manufacturers.
     
IC package substrate used, whether it is R & D or manufacturing in the electronics industry in developed countries such as Japan, South Korea, more mature, but in the country is still in the exploratory stage technology, only Ibiden (Beijing) Co., Ltd., Advanced Semiconductor (Shanghai) Co., Ltd., Zhuhai Doumen Chao Yi Electronics Co., Ltd., one of the few manufacturers in small batches. This is because of China's IC industry is still underdeveloped, but with the multinational electronics giant will continue to move to China IC R & D institutions, and improve China's own R & D and production levels of IC package substrate will have a huge market, is a big vision plant development. China's hard board (single-sided, double-sided, multilayer, HDI board) share reached 70%, of which 5 percent share of the plywood accounted for the largest proportion, followed by soft board with 15.6% of the proportion of second place. Due to the pressure of oversupply, most manufacturers to enter the price war, output growth is lower than expected.      
        
PCB domestic product from the future development trend, output growth is slightly lower than the sales growth was mainly the product gradually to the multilayer structure, the development of high precision. Our multilayer and HDI board is in the business of growing, expanding, increasingly mature technology. MLB is still the mainstream market development; and HDI board by the downstream electronic information products upgrading demand-pull, is in a period of rapid development.

Sophie Deng
_______________________________________
Wonderful PCB Limited
NO.32A,Building NO.1, XianDaiC hengHuaTing,ChuangYeRoad|NanShan District,ShenZhen City 518054|  China  T +86-755-86229518-806 | F  +86 755 2607 3529|  e  wonderful08@wonderfulpcb.com |
w  www.wonderfulpcb.com  | Skype:wonderful-07   |                                                   
Welcome to our trading shows:
1.Booth: L32,Expo Electronic 2013,Apr.10-12th in CROCUS EXPO,Moscow,Russia
2.Booth: 11J36, HK Global sources  Apr.12-15th, 2013 Asia World-Expo, Hong Kong
3.Booth: 9J35, HK Global sources Oct.12-15th,2013 Asia World-Expo, Hong Kong
4.Booth: 70206, CES  2014  Jan,8th-11th in Las Vegas, USA

2015年1月5日星期一

FPC Assembly


Nowadays, technology is already very mature to rigid Printed circuit board, however, many problem may be faced by operator during SMT to FPC.
1 False soldering, short soldering,Tin beads.
2.The Reason is due to the hardness of  raw material of FPC(Flexible printed circuit) caused, FPC is out of shape when meet the hot air and high temperature in reflew machine. Lead the wave shape to FPC, and the slop to FPC pads, then cause the flow of molten tin (liquid tin under high temperature), which cause False soldering, short soldering,Tin beads.(The main reason is the hardness of FPC). So if make the hardness of FPC into the same situation as rigid printed circuit board, and all soldering problem to FPC can be solved. The condition is you should know the SMT process to PCB. And then improve the hardness of Flexible Printed circuit into with the same hardness as rigid PCB, and then FPC SMT can be realized. And some problem, like no fix hole, no mark point, or the FPC is over long, which are the fault of designer, and it is also hard to be solved even to rigid PCB SMT. And NG rate can be only reduced based on personal experience or device independence.

According to above comment, the main solution is to improve the hardness of FPC the same as hardness of Rigid-flex pcb.

B. How to realize stable soldering to FPC
How to get the stable FPC (flexible circuit board) to the rigid PCB welding effects depends on the degree of hardness.
Methods: using jigs(carrier, handling plate) to make FPC perform as rigid board during SMT.

Below is the instruction of Magnetic reflow soldering tray
The material
1. Choose imported alloy material: good flatness, stable performance under high temperature
2. High temperature resistant magnet (300 degrees) to ensure permanent magnet during reflow soldering process.
3.The special steel, with magnetic treatment and good elasticity, and no deformation under high temperature.
4.Performance
(1) Because the flatness to FPC surface cause from the steel pressure l, it can reduce the flow of solder tin during reflow, which can ensure the good quality of soldering and reduce the NG soldering at meanwhile.
(2) Ensure the life of tray when choosing tray material.
(3) Easy and convenient operation with high stability.
(4) Heat insulation, prevent the FPC from deformation
There’s no special requirement to the composition of solder paste of FPC, the size of the tin ball particles and the amount of metal content, etc will be subject to if there is narrow space of IC pins on FPC, BUT FPC has high performance requirements to the solder paste printing, solder paste should has good thixotropy, solder paste should be able to easily be printed , demoulding and can be firmly adhere to the surface of FPC, there will be no mold release lead the hole in stencil filled with tin or such as collapse after printing.

Because FPC fixed on the pallet before SMT,  and the FPC with high temperature heat-resistant pressure-sensitive adhesive tapes for purpose of location, which make its planar inconsistencies, thus FPC printing surface is unlikely to be as smooth as rigid PCB and the same consistent on thickness and hardness, so operator should not use a metal scraper, and should use the polyurethane scraper which with hardness of 80-90 degree.

Solder paste printing machine is best to be with the best optical positioning system, otherwise will have great influence to printing quality, FPC although fixed on the load board, however, there always be small space between FPC and the load board, this is the biggest difference as rigid PCB board, thus the equipment parameters’s setting will also has great influence to the printing effect.

Printing stations is also the key location to prevent FPC from being smudgy, need to wear glove then can go ahead for operation, at meanwhile,  workstation should be kept clean, stencil should be frequently wiped to be clean, to prevent the solder paste to pollute the gold fingers and gold plated key button.

Control of FPC SMT

According to the properties of the products, components quantity and efficiency of mounting, it is OK to adopt high-speed placement machine for SMT. Because every piece of FPC has positioning with fiducial MARK, therefore, there’s no big difference on surface mounting technology between FPC SMD mounting and rigid PCB SMD mounting. It is important to note that although the FPC are fixed on the load board, but its surface can’t be the same flatness like rigid PCB board surface, local space must  exist between FPC and load board, so, the height of suction nozzle’s dropping, compression of blowing should be exactly setted.  On other side, most bare FPC performance as panel; format, and the rate of good finished product relatively low, so it if normal that there’re part of pieces with not good quality, which request recognition function on BAD MARK to SMT machine, otherwise, when mounting FPC panel with the status of not all pieces are good, will show low efficiency.

2014年12月30日星期二

PCB classification


According to the circuit layer classification: divided into single panel, double panel and laminated. Common sandwich plate is commonly 4 layer board or 6 layer boards; complex sandwich plate can reach dozens of layers.

1. Single – Sided PCB

Single panel (Single - Sided Boards) in the most basic on the Aluminum pcb of parts on one side, the conductor is focused on the other side (have SMT components with lead to one side, the plug-in device to the other side).Because the wires in only one side, so this kind of PCB is called Single panel (Single sided).Because single panel in the design of lines, there are many restrictions (because only one side, wiring must around the path alone cannot cross between), so only use this kind of early circuit board.


2. Double - Sided PCB
Double panel (Double - Sided Boards) to both sides of the circuit board wiring, but it took two wires, must have the appropriate circuit connection between two sides. This circuit is called the "bridge" between the guide hole (via).Guide hole is on the PCB, or coated with metal small hole, it can be connected to both sides of the wire. Because the area of the double panel a times larger than a single panel, double panel solved because wiring of the difficulty in the single panel (can be conduction through the hole to the other side), it is more suitable for use in more complex than a single panel circuit.

3. Multi - Layer PCB
Sandwich plate (Multi - Layer Boards) in order to increase the area of the wiring, a multilayer wiring board using the more single or double. With a double lining, two one-way for outer layer or two double lining, two blocks of single outer layer of the printed circuit board, through the positioning system and alternate insulation adhesive materials and conductive graphics interconnection according to design requirement of printed circuit board becomes four, six layer printed circuit board, also known as multilayer printed circuit board. Layer number of the board does not mean that there are several independent wiring layer, under special circumstances will join empty layer to control board thickness, layer number usually is even, and contains the outer two layers. Most of the motherboard is 4 to 8 layer structure, but technical theory can be nearly 100 layers of PCB. Large supercomputers are used quite layers of the motherboard, but because this kind of computer can replace with many ordinary computer cluster, super sandwich plate has not been used gradually. Because each layer of PCB are closely combined, the actual number is generally not too easy to see, but if you look closely at the motherboard, can still see it.

2014年12月29日星期一

PCB Board and Its Advantages to the Industrial Setups 1----Wonderful PCB(hk)Limited



In a very shortest time frame, PCBs or printed circuit boards have turned as the most sophisticated tools used in the electrical equipment domain. In such the competitive market place, importance and gravity of the printed circuit boards can’t be ignored. A PCB or printed circuit board contains highly advanced chips. These applications are placed a very slim plate for some of the components. Manufacturer and developing PCB boards is certainly a tough job that requires massive presence of mind, highly skilled knowledge base and awareness of latest technologies as well.

If experts are to be believed, PCB is an essential device used in almost every industry irrespective of capital, size or strength. A single fault in PCB boards may lead to the big damage and major loss the industry. You may get a number of instances of the PCBs across you. The perfect instance of PCB is motherboard, controller board and different kind of interface cards.

These PCBs have crafted a very special market place in the market and its growing demands are now being fulfilled by numerous manufacturers in the industry.

There are three primary elements of a Printed circuit board namely a laminate board, components mounted on the board and the traces that serve as the wires. The use of actual components in the circuit board is entirely depends upon the purpose and intention of the circuit. Elements used in the PCBs play significant role in finding the Production costs, working efficiency and operating cost of the PCB circuit.lectric layer, a layer of silk screen will be printed. Some words will be printed to show the position of those components. It is also called legend.
PCB finishing
PCB Surface Finishes vary in price, availability, shelf life, reliability and assembly processing. While each finish has its own benefits, in most cases, the process, product or environment will dictate the surface finish that is best suited for the application. It is recommended that the end-user, designer or assembler work closely with their PCB supplier to select the best finish for the specific product design.
If need any more information on PCB, you could check and source from this website: http://www.wonderfulpcb.com Wonderful PCB Technology Co., Ltd is a professional PCB manufacturer for many years and could try best to help!
.
Ms. Jodie Zhou
Wonderful PCB
T +86-755-86229518-807 | F  +86 755 2607 3529|  e  wonderful09@wonderfulpcb.com |
www.wonderfulpcb.com | Skype: wonderful-02   | MSN: wonderfulpcb06@hotmail.com
Welcome to our trading shows:
1. Booth:  L32, Expo Electronics 2013, Apr.10-12th in CROCUS EXPO, Moscow, Russia
2. Booth: 11J36, HK Global sources Apr.12-15th, 2013 Asia World-Expo, and Hong Kong
3. Booth: 9J35, HK Global sources Oct.12-15th, 2013 Asia World-Expo, Hong Kong

PCB Layer Introduction



PCB Signal Layer
The signal layer is mainly used to be placed with the object associated with the signal, which is divided into top, bottom and middle layer . Typically, the top and bottom to place the components and wiring ; intermediate layer is mainly used for the wiring operation.

PCB Power / ground layer
Power / ground layer is mainly used to place the power and ground lines , power and ground circuit components power and ground pin does not need through any copper mold wire connected directly to the power supply and ground lines , and avoid some of the the emergence of design issues , such as ground loop interference.

PCB Mechanical Layer
The function of Mechanical layer is that this layer mainly used to describe the mechanical structure of the Multilayer pcb and place the label instructions, no specific electrical connection characteristics . For example , the mechanical layer may be used to define the physical boundaries of the circuit board in order to avoid Component placed outside the physical boundaries

PCB Mask Layer
The protective layer can be divided into two categories: Solder Mask layer and flux ( Paste Mask ) layer. Solder resist layer is used to protect the copper wire and to prevent the components are soldered to the right place , this layer commonly known as green ink. Generally, the surface of PCB board all covered with solder mask except the place where has pads. In this way to prevent the PCB surface soldered with tin. The flux layer is used to improve pad solderability characteristics. On PCB, the light-colored circular spot which is a little bigger than pad we usually see is the flux layer.

PCB Silkscreen Layer
Silkscreen layer is used to identify the specific location of the various components on the PCB, for example, the components package outline appearance and character , the purpose is to bring convenience to circuit installation and maintenance . Typically , white legends and symbols on the PCB is the silkscreen what often mentioned by human. In PCB field, silkscreen include includes components location , the nominal value , the outer contour of the components and manufacturers logo , production date and so on.

2014年12月28日星期日

Flying Probe test



Flying Probe test is to test some of the major problems of electrical latest solutions. To replace it with a probe needle bed, a plurality of motor-driven can quickly move the probe with the electrical devices of the pin contact and electrical measurements. This instrument was originally designed as a bare board, also requires sophisticated software and program support; has now been able to effectively simulate the online Aluminum pcb test. Flying Probe Test appearance has changed the test method and the low yield rapid conversion (quick-turn) assembled products. Used to take weeks to develop a test a few hours now, and greatly shorten product design cycles and time to market.

Rapid test development; low cost test methods; flexibility fast conversion; well as in the prototype stage to provide rapid feedback to the designer. Therefore, comparing the traditional ICT, Flying Probe test by reducing the time required to make up for the total test time. Flying Probe test system using the benefits outweigh the disadvantages. For example, during assembly, such a CAD system file received after the start of production hours. Therefore, to test the prototype circuit boards for several hours after assembly, not like ICT, high-cost test development process and fixture may be delayed a few days or even a few months. In addition, due to the simple and quick setup, programming and testing, in fact, the general assembly of technical personnel, and not an engineer, you can operate the test. Flying Probe test also exist the flexibility to do a quick test errors quickly convert and process feedback. Also, because the test does not require flying fixture development costs, so it is a typical testing process can be placed in front of the low-cost systems. And because Flying Probe Tester change and rapid test method to convert low-yield assembly, testing usually takes a few weeks to develop a few hours you can get now.

Automatic optical alignment system and the traditional combination of flying machines, the entire automatic optical alignment can make flying more convenient testing and flying in the image processing software dedicated to digital cameras with the help of more accurate. In the traditional Flying Probe test machine, the installation of Flying dedicated to digital cameras and the corresponding image processing software; flying probe testing throughout the automatic identification and detection of the corresponding position to make flying safe and fast test. Having regard to the requirements for fast and precise flying machine, solid industrial hardware and graphics hardware choice, you should first take into account the lightweight, industrial, optical distortion-free, high-speed image processing algorithms; such testing in the actual process of flying because the industry does not appear to affect the hardware itself, the weight of the test accurate, does not appear lost step, and does not affect the image processing algorithm speed flying probe test.