显示标签为“circuit boards”的博文。显示所有博文
显示标签为“circuit boards”的博文。显示所有博文

2015年6月2日星期二

Environmental protection PCB technology


Since the eu formally in December 2003 after "lead-free" legislation, the global electronic has great impact, in July 2006, the European Union WEEE directive about scrap electrical and electronics equipment, electrical equipment on restricting certain pollution substances in the ROHS directive and the Japanese association for the advancement of electronics industry (JEIDA) and the national electrical manufacturers association (NEMl) about the lead, the halogen electronic packaging industry has come into effect, the market of electronic products not contain lead, mercury, cadmium, hexavalent chromium, and restrict the use of polymeric brominated diphenyl or brominated flame retardants, PBB, PBDE harmful substances, such as this will impact of the global supply chain operations, including PCB industry and the development of relevant industries.My company to research environmental protection PCB products since 1999, and became one of the earliest recognized global green partner manufacturers Japan panasonic, and environmental protection and is now 99% PCB products are resonant.In this paper, from the raw material control, the choice of lead-free process and control and SMT electronic encapsulation after three aspects, comprehensively expounds how the next generation of PCB products to meet the increasingly stringent environmental requirements.

The selection and control of raw materials
As is known to all, in the PCB industry, mercury, cadmium and hexavalent chromium are almost don't have to, or in addition to containing trace, in the process of wet process will not be deliberate use of PCB manufacturers, so in the choice of raw materials and process, as long as considering the lead Pb and halogen don't overweight can conform to the basic requirements of environmental protection, metal processing is in be lead-free PCB surface (< 0.1% Pb), the traditional PCB and SMT industry, due to the extensive use of lead, tin alloy, such as HAL, solder paste, etc.Lead is a heavy metal elements, is widely distributed in nature, is the three elements of radioactive uranium and thorium, the end product of the decay of actinium, once the body of the lead intake more than its saturation concentration, can appear the symptom such as anemia, calcium deficiency, weakened immunity.Why do you want to lead-free solder?Leaded solder harmful: lead in solders for the soldering is 1% of the total usage weak (30000/5 million tons), and have widely spread the possibility of difficult to fully recovery.Due to environmental pollution, anxiety, such as lead poisoning effect on human body.In the PCB industry, halogen (fluorine, chlorine Cl, Br Br, 1 F) application mainly on the plate and ink.

material choosing
PCB processing eventually formed on the finished product, mainly includes three types of material: plate, surface processing (metal) layer and ink.1.1.1 plate regular plank FR - 4, CEM - 3, because contain a large number of brominated epoxy resin, such as four bromine bisphenol a, polybrominated biphenyls (PCBS), polybrominated diphenyl ether, etc., in the process of combustion, emit high toxic substances, such as dioxin (TCDO), such as benzene, furan, once the intake will not be able to discharge by human body, greatly threatening the human health.So the PCB must be halogen-free copper clad industry base material chlorine (Cl, Br Br is less than 0.09% respectively), phosphorus (P) epoxy resin instead of brominated epoxy resin, with nitrogen (N) phenol to replace the traditional dicyandiamide curing agent.
In addition, the environmental protection plate also has the strong heat resistance, able to lead-free SMT engineering under 260 degrees high temperature for many times, do not change color, stratification, deformation and bending.

For more information, pls contact: wonderful11@wonderfulpcb.com

2015年4月24日星期五

PCB material appearance defects common measures and industry analysis of commonly used terms

The reason PND (Pits and Dents) pits and depressions occur: fish  any fines particles adsorbed by the edges due to static electricity, the upper plate  residual water Material of the active air drop of dust and debris attached to the copper plate. Solution: identify the problem immediately to re-grind plate and, after washing on the line of the most fundamental solution to reduce staff contact and exposure to air time, to complete the clean room stacked combination of cutting and automatic installation of devices to eliminate static electricity.

  SLP (Slippage) slip occurs:   piece of content R / C high and  flow R / F is greater than the pressure is too easy to produce timely, and every pot temperature is too large and cause uneven flow  substrate per pot Chan will lead to poor positioning piece slip responses: Chan piece R / C, R / F high vertical machine (or water Liquidation machine) can also alter the conditions on Chan laminated CYCLE such as reduced heating rate as amended, postponed the pressure, reduce stress, if a larger temperature difference between each pot can reduce tension lowering capacity to overcome the poor pay more attention to improving the positioning operation.

  Dry (Dried Laminate) board dry Analysis: Poor glass cloth coupling agent compatibility with resin resulting in poor wetting. Or  piece over so that timely pressure hardening resin flow is bad if found to have low flow  board that will produce dry, this condition at the time of solder measured 詴 prone stratification. Solution: glass cloth surface finish problems, please materials manufacturers improved  low traffic reduces varnish water  of time or improve  piece   flow of time and, if not serious Dry Lamination may amend conditions such as increased temperature rate, the pressure on early, increasing pressure. 

2015年3月5日星期四

Multilayer PCB design method (I)

11.2.1 General principles of components layout
7). The serial number of components should be close to the components of the border to decorate, uniform size, direction and tidy, not with components, holes and overlap welding plate. Components or connector pins 1 said direction; Is the sign of the cathode should be clearly marked on the PCB, not allowed to be covered; power conversion components (such as DC/DC converter, linear transformation power supply and switching power supply) side should have enough heat dissipation space and installation space, with sufficient welding outer space, etc.

11.2.2 General principles of the components wiring
Design personnel in the process of Multilayer pcb wiring needs to follow the general principles are as follows.
1)Components printed line spacing of setting principles. Amount of space between different network constraints are produced by electric insulation, process and component size and other factors. Such as a pin spacing is 8 mil chip components, then the chip of the [Clearance Constraint] cannot be set to 10 mil, designers need to separate this chip set a 6 mil design rules. At the same time, the distance between set to take into account the manufacturer's production capacity.
In addition, the influence of components is an important factor in electrical insulation, if two components or network of potential difference is bigger, be considered for electrical insulation problems. In general environment, clearance safe voltage of 200 V/mm, or 5.08 V/mil. So when the same piece of circuit board when there are both high voltage circuit and low voltage circuit, you need to pay special attention to enough safe distance.

2014年12月28日星期日

Through Hole and SMT


Through Hole Mounting: This mounting technique involves different components which have lead wires that are led to the board through holes, hence the name. In this method, leads rely on holes in a multilayer PCB. The leads are then finally soldered to offer permanent mounting. The technology finds usage in DIP aka Dual Inline Packaging and Pin Grid Array Package. 

Surface Mounting: This is a relatively new mounting method worked out seeing a tremendous increase in the number of pins in Integrated Circuits. As demand for smaller weight and size of packaged weight increased, there was felt a need for a new, improved technology that came to be known as surface mount technology (SMT). In this leads are soldered on PCB surface directly rather than using hole mounting. The technology is used in Flatpack Packages and Chip Carrier Packages.

There are some points that make SMT different from Through Hole, which have been briefly summarized below: 
1.SMT has helped significantly in solving the space problems that were commonly noticed with the Through Hole mounting.
2.The pin count has increased greatly in SMT when compared to its older counterparts.
3.In SMT, the components are leadless and are directly mounted to the board surface. In Through Hole the components have lead wires that are taken to the wiring boards via
holes. 
4.The Pads on the surface in SMT are not used for connection of layers on the printed wiring boards.
5.The components in the Though Hole Technology are larger which leads to lower component density per unit area. The packing density that can be achieved with SMT is very high as this allows mounting component on both sides, when needed.
6.SMT has made possible applications that seemed impossible with through hole.
7.SMT is suitable for high volume production that gives access to lowered cost of unit assemblies which is not possible with through hole technology.
8.With SMT acquiring higher circuit speed is easier due to the reduced size. SMT fulfils one of the prime marketing requirements while assisting in making high performance Rigid-flex pcb in a very small size.
9.SMT has a disadvantage as the capital investment involved in its machinery and production is higher.
10.Designing, production, skill and technology required in implementing SMT is very advanced when compared to through hole technology.

When comparing both, SMT surpasses Through Hole in advantages, which clearly define and justify the majority (90%) use of this technology in board assemblies. Through Hole however is anticipated to remain in use in testing and prototype applications that may need manual adjustments and replacements. Its complete disappearance from the scene seems to be ruled out.